FOREX Press I. J. of Electrical & Electronics Research
Support Open Access
  • Home/
  • IJEER-110437

Research Article |

Modeling, Design and Control of Speed DC motor using chopper

Author(s): Rokan Ali Ahmed* and Enas Dawood Hassan

Published In : International Journal of Electrical and Electronics Research (IJEER)        Volume 11, Issue 4

Publisher : FOREX Publication

Published : 23 December 2023

e-ISSN : 2347-470X

Page(s) : 1162-1166

DOI: https://doi.org/10.37391/ijeer.110437

Abstract

An electric motor, a power controller, and an energy-transmitting shaft make up an electrical drive. Power electronics converters are utilized as power controllers in contemporary electrically driven systems. DC actuators and AC drives are the two primary categories of electric drives. This study presents design and modeling techniques for very effective individually stimulated DC motor speed control. A DC motor speed controller can be implemented using a chopper circuit as a converter. The controller transmits a signal into the chopper firing circuit, which in turn generates the desired speed of the chopper by varying the voltage supplied to the motor's armature.One type of controlling loop is the speed controller, and another is the current controller. A proportional-integral controller is used. Eliminating the delay with the aid of this controller makes rapid control possible. It creates a separately stimulated DC motor. A current and speed regulator are built in to give the DC motor high-speed control in a steady condition. Under different speed and torque conditions, the model is simulated and examined in MATLAB (Simulink). Results that are satisfactory are achieved, validating the capacity of the chopper approach to control the speed of a DC motor.

Keywords: Chopper, Current controller, DC drive, DC motor, MATLAB/Simulink, PI controller, Speed control.




Rokan Ali Ahmed*, Department of Electronic Engineering, College of Engineering, University of Diyala, Iraq; Email: rokan.ahmed@uodiyala.edu.iq.

Enas Dawood Hassan, Department of Electronic Engineering, College of Engineering, University of Diyala, Iraq; Email: enashassan808@gmail.com.

    [1] R. K. Antar and A. A. Allu, “Sensorless speed/torque control of DC machine using artificial neural network technique,” Tikrit J. Eng. Sci., vol. 23, no. 3, pp. 55–62, 2016, doi: 10.25130/tjes.23.3.06.
    [2] M. K. Singh and S. Srivastava, “ANFIS based four quadrant chopper control of separately excited DC motor: A literature review,” in 2016 International conference on control, computing, communication and materials (ICCCCM), 2016, pp. 1–6. doi: 10.1109/ICCCCM.2016.7918266.
    [3] Y. A. Ahmed, “Optimal DC machines performance based on intelligent controller,” in IOP Conf. Series: Materials Science and Engineering, 2020, vol. 917, pp. 1–12. doi: 10.1088/1757-899X/917/1/012084.
    [4] V. S. Patil, S. Angadi, and A. B. Raju, “Four quadrant close loop speed control of DC motor,” in 2016 International Conference on Circuits, Controls, Communications and Computing (I4C), 2016, pp. 1–6. doi: 10.1109/CIMCA.2016.8053305.
    [5] A. K. Sahoo and S. Suman, “Speed Control of DC motor Using Hybrid Fuzzy-PID Controller,” Int. J. Adv. Res. Electr. Electron. Instrum. Eng., vol. 6, no. 11, pp. 1–6, 2017, doi: 10.15662/IJAREEIE.2017.0611022.
    [6] Y. I. M. Al Mashhadany, A. K. Abbas, and S. S. Algburi, “Modeling and analysis of brushless DC motor system based on intelligent controllers,” Bull. Electr. Eng. Informatics, vol. 11, no. 6, pp. 2995–3003, 2022, doi: org/10.11591/eei.v11i6.4365.
    [7] S. Masroor and C. Peng, “Event triggered non-inverting chopper fed networked DC motor speed synchronization,” COMPEL-The Int. J. Comput. Math. Electr. Electron. Eng., vol. 37, no. 2, pp. 911–929, 2018, doi: 10.1108/COMPEL-09-2017-0397.
    [8] W. Mohammed Jasim, “Fuzzy Model Reference Adaptive Controller for DC Motor,” Anbar J. Eng. Sci., vol. 8, no. 1, pp. 107–112, 2017, doi: 10.37649/aengs.2017.130744.
    [9] V. R. Teja, S. Balamurugan, and S. S. Kumar, “Development of ALFC and AVR Control Loop as Laboratory Model using DC-DC Buck Chopper,” in 2018 National Power Engineering Conference (NPEC), 2018, pp. 1–5. doi: 10.1109/NPEC.2018.8476742.
    [10] V. K. Chinnaiyan, J. Jerome, J. Karpagam, and S. S. Mohammed, “Design and implementation of high-power DC-DC converter and speed control of DC motor using TMS320F240 DSP,” in 2006 India International Conference on Power Electronics, 2006, pp. 388–392. doi: 10.1109/IICPE.2006.4685403.
    [11] A. Narendra, N. V. Naik, and N. Tiwary, “PV fed separately excited DC motor with a closed loop speed control,” in 2018 IEEE 8th Power India International Conference (PIICON), 2018, pp. 1–4. doi: 10.1109/POWERI.2018.8704449.
    [12] S. Kumari and S. K. Swain, “Optimal control based PID tuning for control of four quadrant chopper fed DC motor,” in 2018 Technologies for Smart-City Energy Security and Power (ICSESP), 2018, pp. 1–6. doi: 10.1109/ICSESP.2018.8376695.
    [13] V. Haji Haji and C. A. Monje, “Fractional-order PID control of a chopper-fed DC motor drive using a novel firefly algorithm with dynamic control mechanism,” Soft Comput., vol. 22, no. 18, pp. 6135–6146, 2018, doi: 10.1007/s00500-017-2677-5.
    [14] L. M. Hassan and J. K. Ali, “Diagnosing the Effect of Misalignment on a Rotating System using Simulation and Experimental Study,” Al-Kitab J. Pure Sci., vol. 6, no. 2, pp. 46–64, 2022, doi: 10.37649/aengs.2022.176355.
    [15] H. Hu, H. Gu, C. Li, X. Cai, and J. Li, “The Design of DSP controller-based DC Servo Motor Control System,” in 2015 3rd International Conference on Advances in Energy and Environmental Science, 2015, pp. 20–25. doi: 10.2991/icaees-15.2015.4.
    [16] S. Keream, “Design and Implementing of a Buck Dc-To-Dc Converter into the DC Motor’s Speed Controller in Matlab/Simulink,” Anbar J. Eng. Sci., vol. 13, no. 2, pp. 36–41, 2022, doi: 10.37649/aengs.2022.176355.
    [17] Z. S. A. Rahman, “Design a Fuzzy Logic Controller for Controlling Position of D. C. Motor,” no. July 2017, pp. 2–7, 2018, doi: 10.13140/RG.2.2.15206.88646.
    [18] O. Prem, B. Kumar, and S. K. Jha, “Intelligent Speed Control of DC Servo Motor Drive,” in 2018 International Conference on Recent Innovations in Electrical, Electronics & Communication Engineering (ICRIEECE), 2018, pp. 3029–3033. doi: 10.1109/ICRIEECE44171.2018.9009138.
    [19] S. Chaouch et al., “DC-motor control using arduino-uno board for wire-feed system,” in 2018 International Conference on Electrical Sciences and Technologies in Maghreb (CISTEM), 2018, pp. 1–6. doi: 10.1109/CISTEM.2018.8613492.
    [20] S. Masroor, C. Peng, Z. A. Ali, and M. Aamir, “Network based speed synchronization control in the brush DC motors Via LQR and multi-agent consensus scheme,” Wirel. Pers. Commun., vol. 106, no. 4, pp. 1701–1718, 2019, doi: 10.1007/s11277-018-5381-6.
    [21] B. A. Kouassi, Y. Zhang, S. Ouattara, and M. J. M. Kiki, “Pid tuning of chopper fed speed control of dc motor based on ant colony optimization algorithm,” in 2019 IEEE 3rd International Electrical and Energy Conference (CIEEC), 2019, pp. 407–412. doi: 10.1109/CIEEC47146.2019.CIEEC-2019179.
    [22] Y. A. Ahmed, Y. I. M. Al-Mashhadany, and M. A. Nayyef, “High performance of excitation system for synchronous generator based on modeling analysis,” Bull. Electr. Eng. Informatics, vol. 9, no. 6, pp. 2235–2243, 2020, doi: org/10.11591/eei. v9i6.2627.
    [23] B. Suresh Kumar, D. Varun Raj, and D. Venkateshwara Rao, “Speed control of BLDC motor with PI controller and PWM technique for antenna’s positioner,” in Emerging Trends in Computing and Expert Technology, 2020, pp. 448–461. doi: 10.1007/978-3-030-32150-5_43.
    [24] H. A. Hussein and A. H. Numan, “The effect of a controlled cooling system on the solar array of DC air conditioner,” Anbar J. Eng. Sci., vol. 11, no. 2, pp. 113–120, 2020, doi: 10.37649/aengs.2023.176834.
    [25] M. Mallareddy, D. P. Chinta, B. Rajpathak, and A. Mitra, “Application of Bio geography based Fractional order PID controller in DC motor drive speed control,” in 2020 IEEE International Conference on Electronics, Computing and Communication Technologies (CONECCT), 2020, pp. 1–6. doi: 10.1109/CONECCT50063.2020.9198663.
    [26] D. Dhara and M. Kule, “A Microcontroller-Based Design of Chopper Circuit for DC Motor Control,” in 2020 International Conference on Computer, Electrical & Communication Engineering (ICCECE), 2020, pp. 1–7. doi: 10.1109/ICCECE48148.2020.9223068.
    [27] A. D. Gangwar, A. Sharma, T. V. P. Singh, and S. Gao, “Fuzzy Logic and PI Based Closed-Loop Speed Control of a Separately Excited DC Motor Using DC-DC Converter,” in 2022 2nd Asian Conference on Innovation in Technology (ASIANCON), 2022, pp. 1–6. doi: 10.1109/ASIANCON55314.2022.9909440.
    [28] A. A. Abd Samat, M. A. Subani, N. F. Ab Aziz, N. A. Salim, K. Daud, and A. I. Tajudin, “PSO-Based PI Controller for Speed Control Of DC Motor,” in 2022 IEEE International Conference on Power and Energy (PECon), 2022, pp. 481–486. doi: 10.1109/PECon54459.2022.9988840.
    [29] S. Bouradi, K. Negadi, R. Araria, B. Boumediene, and M. Koulali, “Design and Implementation of a Four-Quadrant DC-DC Converter Based Adaptive Fuzzy Control for Electric Vehicle Application.,” Math. Model. Eng. Probl., vol. 9, no. 3, pp. 721–730, 2022, doi: org/10.18280/mmep.090319 Received:
    [30] R. K. Antar, A. A. Saleh, and T. T. Yahia, “Estimate and Control speed of a DC motor using Different Power Circuits.,” Prz. Elektrotechniczny, vol. 99, no. 3, pp. 271–276, 2023, doi: 10.15199/48.2023.03.48.

Rokan Ali Ahmed and Enas Dawood Hassan (2023), Modeling, Design and Control of Speed DC motor using chopper. IJEER 11(4), 1162-1166. DOI: 10.37391/ijeer.110437.