Research Article |
Passive Voltage Regulation System for Remote Power Tapping from High-Voltage Transmission OHGW
Author(s): Saad Mohsen Hazzaa1,Baraa Ahmed Shawqi Kamal2, Alyaa Ali Hameed3*
Published In : International Journal of Electrical and Electronics Research (IJEER) Volume 13, Issue 2
Publisher : FOREX Publication
Published : 30 August 2025
e-ISSN : 2347-470X
Page(s) : 429-437
Abstract
It is a real challenge to bring reliable and stable power to remote locations, critical facilities such as telecommunication towers, because it is costly and challenging to expand the conventional power distribution networks. In this paper, a new power supply system is proposed that can overcome this problem by exploiting common overhead ground wire (OHGW) energy transmission lines that run high-voltage (HV). The principle of action is that the system isolates a portion of the OHGW and applies an alternating current (AC) voltage to it by capacitively coupling it to the phase conductors of a transmission line. To take an example, a 4-km span of OHGW on a 735 kV line can produce a maximum power of 25 kW of power which is modelled as a 52.4 kV Thevenin source with the capacitive impedance as 26nF. The main problem is to achieve a stable output voltage (within 5%) across a large load range (0 to 25 kW) without the need for complex control systems, power electronics and so on. To obtain good regulation, this problem is solved using a mix of passive components, nonlinear inductances, and a unique magnetic component, IVACE. Simulation studies have proved that the system could sustain a load voltage of about 62 kV, and the system would be fault resistant and could recover fast with a load disturbance. Harmonic analysis: The value of the total harmonic distortion (THD) is 6.5 per cent at no load and 4.7 per cent at nominal load, with the third harmonics as the most important factor. This method has the advantage as compared to other means of power supply to remote regions, where expansion of the HV transmission network is not needed, and the method is a low-cost and low-maintenance method that can be implemented quickly.
Keywords: High-Efficiency Electrical Systems
, Energy Consumption
, Voltage Stability
, Power Supply
, Remote Applications
, Capacitive Coupling
, OHGW
, Power Regulation
.
Saad Mohsen Hazzaa,Electrical Engineering Department, Tikrit University, Iraq;Email: saad.m.hazaa@tu.edu.iq
Baraa Ahmed Shawqi Kamal , Electrical Engineering Department, Tikrit University, Iraq;Email: Baraa.k.78@gmail.com
Alyaa Ali Hameed, Electrical Engineering Department, Tikrit University, Iraq;Email: alyaa.ali@tu.edu.iq
-
[1] G. Halhoul Merabet et al., “Intelligent building control systems for thermal comfort and energy-efficiency: A systematic review of artificial intelligence-assisted techniques,” Renew. Sustain. Energy Rev.., vol.. 144, no. August 2020, p. 110969, 2021.
-
[2] D. Mylène, Review of optimisation methods for the design of power electronics systems. 2020.
-
[3] A. Messac, Optimisation in Practice with MATLAB®. Cambridge University Press, 2015.
-
[4] G. Lei, J. Zhu, Y. Guo, C. Liu, and B. Ma, "A review of design optimisation methods for electrical machines," Energies, vol. 10, no. 12, 2017.
-
[5] A. Smirnov, N. Uzhegov, T. Sillanpaa, J. Pyrhonen, and O. Pyrhonen, "High-Speed Electrical Machine with Active Magnetic Bearing System Optimisation," IEEE Trans. Ind. Electron., vol. 64, no. 12, pp. 9876–9885, 2017.
-
[6] S. Lee, G. Park, and H. Jeong, “Design of High-Speed, Low-Power Sensing Circuits for Nano-Scale Embedded Memory,” Sensors, vol. 24, no. 1, 2024.
-
[7] M. A. Khan, C. Hankendi, A. K. Coskun, and M. C. Herbordt, "Software optimisation for performance, energy, and thermal distribution: Initial case studies," 2011 Int. Green Comput. Conf. Work. IGCC 2011, no. February 2011.
-
[8] K. Ahn, E. Bayrak, and P. Papalambros, "Electric Vehicle Design Optimisation: Integration of a High-Fidelity Interior-Permanent-Magnet Motor Model," Veh. Technol. IEEE Trans., vol. 64, pp. 3870–3877, Sep. 2015.
-
[9] I. Petri, S. Kubicki, Y. Rezgui, A. Guerriero, and H. Li, "Optimising energy efficiency in operating built environment assets through building information modelling: A case study," Energies, vol. 10, no. 8, pp. 1–17, 2017.
-
[10] B. Gilev, N. Hinov, and S. Stefanov, "SOFTWARE IMPLEMENTATION OF METHODS FOR OPTIMAL DESIGN OF POWER ELECTRONIC DEVICES," Int. J. Inf. Technol. Secur., vol. 15, no. 2, pp. 35–46, 2023.
-
[11] G. Lei, J. Zhu, Y. Guo, C. Liu, and B. Ma, "A review of design optimisation methods for electrical machines," Energies, vol. 10, no. 12, p. 1962, 2017.
-
[12] A. Smirnov, N. Uzhegov, T. Sillanpää, J. Pyrhönen, and O. Pyrhönen, "High-speed electrical machine with active magnetic bearing system optimisation," IEEE Trans. Ind. Electron., vol. 64, no. 12, pp. 9876–9885, 2017.
-
[13] A. Palaniappan and S. Palermo, "A design methodology for power efficiency optimisation of high-speed equalised-electrical I/O architectures," IEEE Trans. Very Large Scale Integration. Syst., vol. 21, no. 8, pp. 1421–1431, 2012.
-
[14] A. Sivasubramaniam, M. Kandemir, N. Vijaykrishnan, and M. J. Irwin, “Designing energy-efficient software,” in Parallel and Distributed Processing Symposium, International, 2002, vol. 2, pp. 8-pp.
-
[15] K. Ahn, A. E. Bayrak, and P. Y. Papalambros, "Electric vehicle design optimisation: Integration of a high-fidelity interior-permanent-magnet motor model," IEEE Trans. Veh. Technol., vol. 64, no. 9, pp. 3870–3877, 2014.
-
[16] A. Avwioroko and C. Ibegbulam, “Citation: Avwioroko A. and Ibegbulam C. (2024) Contribution of Consulting Firms to Renewable Energy Adoption,” Int. J. Phys. Sci. Res., vol. 8, pp. 17–27, Jun. 2024.
-
[17] A. Folorunso, O. Babalola, C. Nwatu, and A. Adebisi, “A comprehensive model for ensuring data compliance in cloud computing environment,” World J. Adv. Res. Rev.., vol. 24, pp. 1983–1995, Nov. 2024.
-
[18] P. Chijioke, Agupugo, A. Ajayi, C. Agupugo, C. Nwanevu, and C. Chuku, Review of penetration and impact of utility solar installation in developing countries: policy and challenges, vol. 7. 2024.
-
[19] K. Bassey, “From waste to wonder: Developing engineered nanomaterials for multifaceted applications,” GSC Adv. Res. Rev.., vol. 20, pp. 109–123, Sep. 2024.
-
[20] A. Agarwala et al., “Towards next generation power grid transformer for renewables: Technology review,” Eng. Reports, vol. 6, no. 4, pp. 1–31, 2024.